We routinely produce dsRNA by in vitro transcription of a PCR generated DNA template containing the T7 promoter sequence on both ends (I. Primer Designed dsRNA). It is also possible to produce dsRNA using PCR generated DNA templates containing either the T7 SP6 or the T7 T3 promoters on either end (II. dsRNA Fom Clones). This method is less efficient, especially when working on a large scale. All work should be done in a sterile, RNase free environment, using only sterile, RNase free solutions and materials, and while wearing gloves do reduce contamination. Templates can be generated by PCR on cDNA (including ESTs from BDGP), genomic DNA, or first strand RT-cDNA. Most of the dsRNA should correspond to exons but dsRNA with two or more exons interrupted by introns will also work well. We generally aim for ~500 bp products although RNAi with products ranging from 150-3000bp have been shown to work. The target sequence should not contain complete 21-mer homology to other genes or your dsRNA could be non-specific. One case has been seen where the template contained one mismatch in a 21-mer identical stretch to another gene, and still only the level of the intended target was reduced, while the close homologue was unaffected. Since the targeted region within a transcript may influence the success of RNAi , the safest approach is to use dsRNA corresponding to the 5 or 3 UTR. It is recommended to check the various sequence sources (Publications, NCBI and BDGP, genomic and ESTs) to confirm the primary sequence of a given gene. We suggest using the Primer3 website ( http://www-genome.wi.mit.edu/cgi-bin/primer/primer3_www.cgi) for designing primers. Complementary sequences should be 20-24 nt, the Tm range between 59?C - 61?C and optimize against self-annealing by setting the Max Complementarity to 5 and Max 3 Complementarity to 1. After choosing the primer sequence, add the T7 promoter sequence (TAATACGACTCACTATAGGGAGA) to the 5 end. Perform a standard 50 or 100 l PCR reaction using your selected primer sequences to amplify the region of interest. Use 1-2 l of a 10 M primer stock, 100-200 ng DNA as template and DNA polymerase. We have successfully used GeneChoice Taq (PGC Scientifics #62-6086-01), TaqPlus (Stratagene #600210), and Herculase (Stratagene #NC9690330) in the following PCR reaction conditions: 94℃ - 3 min. 94℃ - 45 sec. 57℃ - 30 sec. 72℃ - 45 sec. steps 2-4, 30x 72℃ - 10 min.li Check the PCR results to ensure that you have a band of the expected size. I run 4ul in a 1% agarose gel and use the small combs. I also us a 250bp ladder. We use the Ambion MEGAscript T7 kit (Cat.# : 1334) for the transcription reaction. Follow the Ambion MEGAscript kit protocol for Transcription Reaction Assembly and use 5 l of PCR template per 20 l reaction. It is not necessary to purify the PCR template before transcription. We incubate the reaction in a heat block or thermocycler for 4 hours. Following incubation, we remove the DNA template with the DNase. Transcription and annealing occur simultaneously and no additional step is required to anneal the two complementary. If you want more dsRNA, scale up the reaction. Confirm that the dsRNA product is the correct size using a 1% agarose gel with TBE or TAE buffer and load only 0.5 l. Purify using Qiagen s RNAeasy (#74104) or Ambion s NucAway Spin Columns (#10070). Ambion also has a MEGAclear column which is reported to work but has not been tested in this lab. When using Qiagen s RNAeasy columns, follow the RNA cleanup protocol and elute twice to maximize yield. Also, if you scale up the 20 l reaction and are using Qiagen s RNAeasy columns, divide the reaction and purify in two or more columns in order to not overload a single column. If you are performing reactions in a 96 well format, purify the dsRNA in Millipore Multiscreen PCR plates (#MANU03050). In our opinion, the Qiagen RNAeasy 96 well plates often perform inconsistently and can be difficult to use. Measure the OD 260 of 1:50 dilution. Calculate the concentration by measuring the OD 260 of 1:50 - 1:100 dilution. Then multiply the OD260 by the dilution factor and an extinction coefficient of 45 (dsRNA Concentration = OD260 x Diln. x 45). The standard output of 20 l reaction is 80 - 200 g, with 120 g as a frequently observed value. The dsRNA can be stored at -20℃, or at -70℃ as a precipitate with 0.1x sodium acetate and 2.5x ethanol. Templates can be generated by PCR using purified plasmid as a template. The entire inserted sequence can be amplified using T7 SP6 or T7 T3 promoter primers depending on the plasmid. Check the PCR results to ensure that you have a band of the expected size. We use the Ambion MEGAscript T7, T3, SP6 kits (Cat.# : 1334, 1338, 1330) for the transcription reaction. With T7 SP6 or T7 T3 promoters, each transcription reaction will occur in a separate tube. Follow the Ambion MEGAscript kit protocol and use 5 l of PCR template per 20 l reaction. It is not necessary to purify the PCR template before transcription. When the reactions are complete (generally after 2-4 hours) check 0.5 l of each product on an agarose gel. Purify each strand using Ambion s NucAway Spin Columns. I would not advise using the Qiagen RNAeasy columns due to the fact that the two strands never annealed after using them. To anneal, combine equal molar amounts of each transcript into one tube. Then, place the tube in a boiling water bath, turn the heat off, and leave overnight to anneal. Check again on a 1% agarose gel, measure the concentration, aliquot, and store. Worby CA, Simonson-Leff N, Dixon JE. (2001) RNA interference of gene expression (RNAi ) in cultured Drosophila cells. Sci STKE (95):PL1. 超方便的实验干货查询工具 微信扫码进入「丁香实验」小程序 查看全部 来源：互联网 超方便的实验干货查询工具微信扫码进入「丁香实验」 知道了 你可能喜欢 手把手教你设计引物（图文并茂）